-Main Page
   -Guides
   -Reviews
   -Tech Bits
   -Case Gallery
   -Forums
   -Wireless
   -Contests!
   -Affiliates
   -About Us
   -Droid Hype

   Manufacturers:
   -IWill USA
   -Matrox
   -Samsung USA
   -Crucial
   -Toshiba
   -Actiontec
   -M-audio
   -EverGreen Tech
   -EPI USA
   -Buffalo Tech
   -ThermalTake
   -Zalman Tech
   -Cyber Cooler
   -Vantec USA
   -Evercool
   -Chenbro
   -CoolerMaster
   -C3
   -SuperPower
   -Lian Li
   -2CoolPC
   -Icemat
   -TweakMonster
   -Cobalt3
   -Sunbeam
   -ShatteredWeb
   -Tagan
   -Rosewill
   -EDGE Memory
   -Eagle Tech

   Online Shops:
   -CrazyPC
   -HighSpeed PC
   -UmaxPC
   -Xoxide Mods
   -Directron
   -Azzo
   -Computer Geeks
   -CensusPC

.: Random Case Gallery User uploads :.
Mahogany USB Drive
Sharing cellphone broadband
Making acrylic fan grills
 

LapLogic Aerogel Extreme
EDGE DiskGO 160GB Network HDD
GelaSkins for DS and PSP

-- Sunbeam LED Case Feet
-- Category: Review
-- Posted by: dave303
-- Posted on: 2006-01-16
-- Price: ~ $9.99 USD
-- Pages: 1 [ 2 ]
Digg this article
Submit to reddit
Add to del.icio.us
Submit to Slashdot
Stumble this article!

Each replacement foot needs to be taken apart so you can attach it to the case. There are two small screws holding a plastic cover. It lifts up and you have three pieces to replace the old two piece foot.

 

 

 

 

 

 

First you will need to feed the pig tail into the hole that holds the base clip. It has a small slit in it so the wires will feed through there without binding up.

Replace the case screw that holds it all in place. Then attach the last cover piece with the LED. Tighten the small screws that holds the little cover on to finish it off.

The below picture has a small arrow to one of the small screws. On three of the feet one screw was stripped out so I was not able to remove them with out some moddifaction...Dremel time. The screws were changed from the phillips to a slotted screw top. First one I ran across made me wonder if I messed up the screw heads but I did check out the others and found them to be faulty also. The modded change didn't take long and everything else went together fine.

So I put the case back together and grabed a few pictures as the case sits in the dark. Front view with one of the LED fans glowing like a champ as well as the feet. The other fan is not as bright. The two LEDs give off more light than my two year old CCFL that is sitting at the bottom of the case.

Over all it does add more light to the case. A couple of road blocks that I had were the stripped heads. At $9.99, it's quite an affordable addition to your case. If your case is not supported, you can still install these feet. Sunbeam has included instructions to modify your case to make these fit.



Pros:

  • Bright LED
  • Markings on the power rail
  • Easy install


Cons:

  • Three bad small screws
  • Instructions could use a proof read

< Previous Discuss this in our Forums! >

Page: 1 [ 2 ]


Bandwidth sponsored by SCHostPro.com

Latest Updates

LapLogic G800/W800 Areogel Extreme
LapLogic G800/W800 Aerogel Extreme

Mahogany USB Drive
Mahogany USB Drive

EDGE Tech DiskGO NAS 160GB
EDGE DiskGO 160GB
Network HDD

GelaSkins for DS and PSP
GelaSkins
DS and PSP


All trademarks used are properties of their respective owners. All rights reserved.
Copyright © 1999 - 2017 by GideonTech.com

Page was generated in 0.018774 seconds

Partner Links: Shorty.org

Our Friends - GideonTech | Metku | AllTheMods | OCModShop | Bona Fide Reviews | Rbmods | ThinkComputers | PCApex | TweakTown