-Main Page
   -Tech Bits
   -Case Gallery
   -About Us
   -Droid Hype

   -IWill USA
   -Samsung USA
   -EverGreen Tech
   -Buffalo Tech
   -Zalman Tech
   -Cyber Cooler
   -Vantec USA
   -Lian Li
   -EDGE Memory
   -Eagle Tech

   Online Shops:
   -HighSpeed PC
   -Xoxide Mods
   -Computer Geeks

.: Random Case Gallery User uploads :.
Mahogany USB Drive
Sharing cellphone broadband
Making acrylic fan grills

LapLogic Aerogel Extreme
EDGE DiskGO 160GB Network HDD
GelaSkins for DS and PSP

-- SuperPower Zephyr KS-201 ATX Case
-- Category: Review
-- Posted by: GideonX
-- Posted on: 2001-08-23
-- Price: ~ $NA USD
-- Pages: 1 2 [ 3 ] 4 5
Digg this article
Submit to reddit
Add to del.icio.us
Submit to Slashdot
Stumble this article!

Once we popped open the sides, we took a look into the interior. First impressions of the case from the look of things is the structured feel of the whole thing. No edges were sharp or unfinished and everything was positioned at a convenient spot.


The usual bag of goodies was included along with a 3 prong power cord and a spec sheet. There are enough screws to build a system and then some. If you lose these screws like I do, this is a good back up for any future upgrades.

Staring into the bowels of the case, I noticed the silver motherboard standoffs (nipples) were already installed for us. I usually have a great deal of trouble putting these on due to my pudgy fingers (no jokes Kile!) Having them already installed for me was a plus.

Included with our sample was a 300W AMD approved power supply. Manufactured by Super Power themselves, this should suffice for powering almost all AMD/Intel based systems.

Right below the power supply is the rear exhaust fan. Its shielded by a plastic covering which I think prevents any fingers from getting hurt. There is also another fan situated at the bottom front that sucks in the cold air. The bottom covering houses the fan and the case speaker. The fan used is labeled Power Cooler, a sleeve bearing fan. You probably would want to change this. You may receive a different fan than ours in your own sample.

The front bezel connectors are all labeled accordingly. One thing that still gets me is the labeling on most motherboards never correspond with the connectors on the cases. Its like the hot dog bun dilemma, where there are 6 buns and 8 hot dog wieners. Ok, bad analogy.

The 3.5" drive cage can be removed, which makes installing new hard drives a whole lot easier. One 3.5" bay is hidden, while two are exposed. You can remove the cage by taking off the one screw on the side. The four 5.25" are spacious, there is about 8-9 inches of space between the power supply and the start of the 5.25" drive bays. Ample room to stick your hands in to work on things.

Here is a shot of the expansion slots, nothing surprising here. Again, I'll stress the ease of taking these apart and putting them back due to the fact that the spacers have notches at the end. Small observation but it goes a long way in the long run. For me at least.

The motherboard tray does not slide out unfortunately. There are holes on the back that allow you to screw in the 3.5" drives if you don't plan on removing the drive cage.

< Previous Next >

Page: 1 2 [ 3 ] 4 5

Bandwidth sponsored by SCHostPro.com

Latest Updates

LapLogic G800/W800 Areogel Extreme
LapLogic G800/W800 Aerogel Extreme

Mahogany USB Drive
Mahogany USB Drive

EDGE Tech DiskGO NAS 160GB
Network HDD

GelaSkins for DS and PSP
DS and PSP

All trademarks used are properties of their respective owners. All rights reserved.
Copyright © 1999 - 2019 by GideonTech.com

Page was generated in 0.041448 seconds

Partner Links: Shorty.org

Our Friends - GideonTech | Metku | AllTheMods | OCModShop | Bona Fide Reviews | Rbmods | ThinkComputers | PCApex | TweakTown